|
|
| Dual Flush conversion Kit by SelectAFlush |
| SelectAFlush is a Leader for the Industry
At SelectAFlush, we strive to be a leader in creating innovative products that will  conserve water. Our current product is a dual flush toilet valve. Yes, they have dual flush, low flow, high efficiency toilets available right now and if you would like to buy brand new toilets for your residential or commercial properties we encourage you to do so. However, if you are like most Americans trying desperately to conserve without spending an enormous amount of money, then we suggest you purchase our new dual flush valve to fit in your existing toilets.
Our mission at SelectAFlush is to provide a product that incorporates a positive commercial and personal impact on our environment.
We have designed an easy to install flush valve using ONLY American ingenuity, resources and labor. Never again sacrifice flushing performance by using a brick or water bag. Often, a brick or water bag requires a double flush that actually wastes water. Our Patent Pending dual flush valve offers a liquid rinse flush when pushed left, or full flush when pushed to the right.
SelectAFlush easily installs in minutes using highly engineered, long lasting seals that will not leak. Now you can save water on all standard two piece toilets designed for a 2 flush valve. Simply replace any flapper flush valve with SelectAFlush and start reducing your water consumption immediately. Imagine saving thousands of gallons of water per year without sacrificing convenience or performance. Our product can save more water than a low flow toilet when installed on a 3.5 gallon toilet or smaller.
Our retro fit flush valve will save over 7 million gallons per year per 1000 installations on 3.5 gallon toilets. BE ONE IN A THOUSAND or better yet, BE ONE IN A MILLION. A little flush goes along way.
Convert your current toilet over to a dual flush with a product like SelectAFlush, dual flush conversion kit. Cost $39.95 (1.1 to 2.5 gallons of water per flush average) *Note: A dual flush is rated in two ways: an average between the two flushes or a 4 to1 average. This is an average range we have seen:
-
Installed on a 1.6 gallon toilet, light flush capacities from .8 to 1.1 gallons and heavy flush capacities from 1.3 to 1.6 gallons per flush.
-
Installed on a 3.5 gallon toilet. Light flush capacities from 1.1 to 2 gallons and heavy flush capacities from 2.5 to 3.3 gallons per flush.
-
Installed on a 5 gallon toilet, light flush capacities from 2.2. To 3 gallons and heavy flush capacities from 3.8 to 4.5 gallons per flush.
-
Installed on a 7 gallon toilet ( maybe its time for an upgrade but if not) light flush capacities from 3 to 5.5 gallons and heavy flush capacities from 4 to 6.5 gallons per flush.
Save our precious resource WATER
Save our precious resource ENERGY
Save YOUR precious resource $$ MONEY $$
Features:
-
Dual Flush Toilet Valve
-
Dual Action Flush Lever
-
Long Lasting Silicone Seals
-
Easy To Install Instructions
-
SelectAFlush Decal
-
All Inclusive Parts in Packaging
Benefits:
-
Empowers every consumer to save water
-
Lowers water and sewage bills
-
Saves 7 million gallons of water per thousand installations per year*
-
Extends the life of higher water consumption toilets saving landfill space
-
Can enhance solid flush performance
-
Reduces impact on municipal sewage treatment systems and saves energy
-
Alleviates strained capacity on water treatment plants
-
Reduces impact on septic systems
-
Provides a powerful and positive impact on our environment
View our Certification 
| |
|
SelectAFlush dual flush conversion kits fit over 80% of all existing two piece residential style toilets. It will save water in 1.6 gallon and larger toilets with left and right hand front facing levers. It will NOT fit on toilets with handles on the SIDE or CORNER of the tank at this time. We also require 7/8" clearance from the edge of the tank to the edge of the currently installed flush valve.
For more fit delails look at our FAQ pages
|
Follow us www.twitter.com/dualflushkit We help people save water
At SelectAFlush, we want to enable our consumers
to make a difference by improving their current products.
| WE CAN'T FAST FORWARD THE FUTURE BUT WE CAN MAKE THE PAST BETTER FOR THE ENVIRONMENT IN THE MEAN TIME. |
Imagine not only saving YOUR money but helping the environment effortlessly! Why would you even think about not participating along with millions of others who have changed the way they live and "Gone Green"!
Go green, be a powerful force in your community, spread the word that there are simple ways to save water, energy and money. See our tips for the day! Browse our website! Enjoy being green!!
|
Testimonials
"I have 7 daughters under the age of 16, you have no idea how much water they can waste. I am now saving in all 5 of our bathrooms"! Thank You SelectAFlush
Dual Flush believer - Tom, Boynton Beach, FL Owner of BGI Growers
|
|
|
|
| Select A Flush Blog |
Why does anyone need an MaP rated toilets?
Oct 27th,2009 |
The first practical flush toilet was patented in 1778 in Yorkshire, England. Fast forward 102 years and Thomas Crapper, the son of a steamboat captain and a journeyman plumber, began to popularize the flush toilet. Crapper sold toilets 125 years before MaP ratings were invented to the most critical buyers of his time, the English royal family.
Since 1880 billions of toilets have been sold without MaP certification. The Manufacturer's knew that if their toilet didn't flush away solid human waste, they wouldn't sell. Then in 2003 hell broke loose. Did it really? Na, that's an overstatement. Did your toilet back up in 2003? No? Same here. It kept right on flushing away in spite of the the flushsble diapers, and a whack of other flushables. Still people don't come up with standards for no reason.
MaP exists because a group of companies who make toilets were stampeded into changing their design overnight and the designs were bad, so the toilets clogged. Was this whole thing was a scam? Did 6
liter toilets have no other history before 2003? Of course they did.
Holland has been using low flush toilets for over a generation. Are the CEOs of all the North American Manufacturer's incompetent? Not on your life.
So one is left to wonder, with the toilets already well designed and in use for 30+ years elsewhere, how did highly competent North American toilet factories get so screwed up? Was it deliberate?
Couldn't they have imported from Europe or Australia for 6 months as their own production got ramped up? Was the failure intentional with the thought being that a bunch of deliberately faulty toilets could be sold and replaced thus doubling profits? We're more moral than that, aren't we? You decide.
Assuming everyone had the same good intentions, to conserve water, the actual toilets wasted:
tax money,
consumer money,
plumbers time,
installation money, and
They actually used more water because multiple flushes were needed.
Even the cartoonists who make "King of the hill" made an episode about it.
Those badly made toilets need never have existed nor did we need to create MaP tests to prove they do. All anyone needed was a simple dual flush toilet valve which costs a fraction of what a new toilet costs and reduces water use in a toilet by 40%. With Selectaflush a sane toilet flusher can reduce the average flush size to 7.8 liters in an existing 13 liter toilet.
Selectaflush dual flush mechanisms are in use all over the USA and Canada now and customers are saving money and the environment without replacing a single toilet. |
A caution on advice from those purporting to be expert about Dual Flush Toilet Conversion Devices
Oct 26th,2009 |
| During the past year, a small number of those claiming to be the only experts who know anything about water efficiency have been approaching governments and regulatory bodies to warn them about dual flush toilet mechanisms. They have no experience in the testing or manufacturing of dual-flush mechanisms and so paying them heed is being questioned.
A number of intelligent, and environmentally aware people are converting their 1.6-gallon (6.0-litre), 3.5-gallon (13-litre), 5-gallon (19-litre) or more fixtures from a single-flush, tank-type gravity toilet to a dual-flush toilet and saving significant amounts of money simply by converting the mechanism within to dual-flush. My own water bill is 80.00 a year less. The essence of a dual flush mechanism is that it offers 2 sizes of a toilet-flush, which can’t help but save us money. In many cases toilet makers oppose the sale of these devices, as they are the one thing that changes the essence of how a toilet operates. Additionally, if they don’t sell more porcelain, they won’t make any money. Since the vast majority of people have a toilet, that can absolutely be made to be more efficient, this is cause for doubt about the motivation of those pushing us to buy toilets
While the goal of reducing water use in the home is admirable, there are endless cases in which low flow toilets have been shown to clog, require more water to actually flush away solid waste, are not built in concert with proper engineering of the rest of the plumbing system, and are of questionable financial- and life-value. Two primary reasons for this are…
(1) The removal and replacement of an older piece of equipment with a new low-flush toilet ignores the reality that the plumbing in every building was engineered to carry solid waste with a given volume of water. A lack of that water leads to solid matter lying still in a pipe, which becomes a clog beyond the toilet. This is especially so in MURBs, (Multiple Unit Residential Buildings). The finest experts will agree that 1.6-gallon and 1.28-gallon toilets have finely tuned hydraulic characteristics. Such tuning helps allow a smaller amount of water to move waste through the toilet bowl. The aging, less finely tuned pipes that the waste flows into have are an enormous problem. Failure to change the profile of the plumbing pipes will adversely affect flow performance, leading to total system clogging. In a perfect scenario, a new 6-liter toilet would be used with plumbing that is on a greater slope and which has a much smoother interior than almost all-existing sewage pipes in all buildings.
(2) Every toilet has a carbon footprint. That footprint is a function of mining, drying, firing, glazing and transporting porcelain. So, while some water is conserved through lower flushes, enormous amounts of Co2 are being emitted into the atmosphere which in turn causes global warming, and a decrease in the pH levels of the oceans (an increase in acidity) Most of the factories are based in China where the primary source of energy is low quality coal. 80% of all energy in China is generated with burning coal. At this point few if any Chinese industrial cities have air that is clean enough to be able to meet the more relaxed Chinese air quality standards, which are far below those of other parts of the industrialized western world. Many of the cities are so badly smog-ridden airplanes are regularly rerouted, as visibility is too poor to see to land.
Other factors to be considered by those installing, recommending, or subsidizing these low-flow toilet products are:
(1) Ethics of manufacturers that knowing sold the North American Population toilets that were not properly engineered.
(2) Redundant making of porcelain fixtures leads to equally un-necessary installation costs, transportation costs and income taxes.
In conclusion, the purchase, endorsement, or subsidy of these low-flow toilets should be
approached with much caution and eyes wide open. If an individual or agency wishes to proceed, however, they should: (1) insist upon full repayment of amount received for sales of 6 L toilets that were previous supplied and clogged from day one due to mismatched tanks and bowls; (2) require that the product be installed in properly engineered buildings only with plumbing that does the job of carrying solid waste through the entire plumbing system; and (3) insist that the manufacturer prove he has considered the necessary slope of the pipe, diameter, and materials, and the probable condition of the pipe materials after varying lengths of time in use beyond the individual toilet (e.g. cast iron, clay, plastic, and so on) and that the waste will actually move
Finally, it is our opinion that the water savings potential and cost-effectiveness is much greater with the use of toilet retrofit devices even if the toilets meet the above requirements, as the air pollution at stake is staggering. At such time that a toilet meets the standard, is independently tested, and demonstrates that it will not adversely affect the overall performance of plumbing or do harm to the environment, we will report that information
W. Golley |
|
|
|
 |
|
|
Testimonials
"I have 7 daughters under the age of 16, you have no idea how much water they can waste. I am now saving in all 5 of our bathrooms"! Thank You SelectAFlush
Dual Flush believer - Tom, Boynton Beach, FL Owner of BGI Growers
|
|
|
|
|
|
